Phase composition,microstructure and thermophysical properties of the Srx(Zr0.9Y0.05Yb0.05)O1.95+x ceramics

Sr_x(Zr_0.9Y_0.05Yb_0.05)O_1.95+x (x=1.0, 0.9, 0.8, 0.7) ceramics were prepared by solid state reaction sintering. The sintered Sr_1.0(Zr_0.9Y_0.05Yb_0.05)O_2.95 is a single-phase solid solution while the sintered Sr_x(Zr_0.9Y_0.05Yb_0.05)O_1.95+x (x=0.9?0.7) are composites, and a significant grain growth inhibition is observed in the sintered Sr_x(Zr_0.9Y_0.05Yb_0.05)O_1.95+x (x=1.0, 0.9). Rare-earth elements distribution in the bulk materials indicates that Yb and Y preferentially substitute Zr-sites in SrZrO₃, and the highest solubility of RE₂O₃ in pure SrZrO₃ is ～0.8 mol%. The sintered Sr_x(Zr_0.9Y_0.05Yb_0.05)O_1.95+x have high thermal expansion coefficients up to ～11.0×10^?6 K^-1 (1200°C). Sr_0.8(Zr_0.9Y_0.05Yb_0.05)O_2.75 has the lowest thermal conductivity of 1.38 W·m^-1·K^-1 at 800°C. Sr_x(Zr_0.9Y_0.05Yb_0.05)O_1.95+x (x=1.0, 0.9, 0.8) show no phase transition from 600 to 1400°C, whereas Sr_x(Zr_0.9Y_0.05Yb_0.05)O_1.95+x (x=0.9, 0.8) have excellent high-temperature phase stability over the whole investigated temperature range. Therefore, Sr_x(Zr_0.9Y_0.05Yb_0.05)O_1.95+x (x=1.0, 0.9, 0.8) are considered as promising TBCs materials that might be operated at higher temperatures compared to YSZ.     

Toward a better understanding of multifunctional cement-based materials: The impact of graphite nanoplatelets (GNPs)

The impact of graphite nanoplatelets (GNPs) on the physical and mechanical properties of cementitious nanocomposites was investigated. A market-available premixed mortar was modified with 0.01% by weight of cement of commercial GNPs characterized by two distinctively different aspect ratios.The rheological behavior of the GNP-modified fresh admixtures was thoroughly evaluated. Hardened cementitious nanocomposites were investigated in terms of density, microstructure (Scanning Electron Microscopy, SEM and micro–Computed Tomography, μ-CT), mechanical properties (three-point bending and compression tests), and physical properties (electrochemical impedance spectroscopy, EIS and thermal conductivity measurements). At 28 days, all GNP-modified mortars showed about 12% increased density. Mortars reinforced with high aspect ratio GNPs exhibited the highest compressive and flexural strength: about 14% and 4% improvements compared to control sample, respectively. Conversely, low aspect ratio GNPs led to cementitious nanocomposites characterized by 36% decreased electrical resistivity combined with 60% increased thermal conductivity with respect to the control sample.     

Low thermal conductivity in porous SiC–SiO2–Al2O3–TiO2 ceramics induced by multiphase thermal resistance

The introduction of multiple heterogeneous interfaces in a ceramic is an efficient way to increase its thermal resistance. Novel porous SiC–SiO₂–Al₂O₃–TiO₂ (SSAT) ceramics were fabricated to achieve multiple heterogeneous interfaces by sintering equal volumes of SiC, SiO₂, Al₂O₃, and TiO₂ compacted powders with polysiloxane as a bonding phase and carbon as a template at 600 °C in air. The porosity could be controlled between 66% and 74% by adjusting the amounts of polysiloxane and the carbon template. The lowest thermal conductivity (0.059 W/(m·K) at 74% porosity) obtained in this study is an order of magnitude lower than those (0.2–1.3 W/(m·K)) of porous monolithic SiC, SiO₂, Al₂O₃, and TiO₂ ceramics at an equivalent porosity. The typical specific compressive strength value of the porous SSAT ceramics at 74% porosity was 3.2 MPa cm³/g.     

A comparative study on the effect of carbon-based and ceramic additives on the properties of fiber reinforced polymer matrix composites for high temperature applications

Ablative composites have been in use for thermal protection of space vehicles for decades. Carbon-phenolic composites have proven to perform exceptionally well in these applications. However with development in aerospace industry their performance needs improvement. In this field, different carbon-based and ceramic additives have been introduced into ablative composite systems. This review article gives a comparative analysis of researches done in this field in the recent past. Density, ablative, thermal and mechanical properties of ablative composites with different ultra-high temperature ceramic particles i.e. ZrSi₂, Cenosphere, nano-SiO₂, BN etc. and carbon-based nanoparticles i.e. CNTs, nano-Diamonds, Graphene oxide etc. used as additives, have been compared and discussed. Emphasis is put on carbon-phenolic composite systems although some epoxy matrix systems have also been discussed for comparison.     

Mechanical properties and thermal shock in thin ZrO2–Y2O3–Al2O3 films obtained by the sol-gel method

Thin multilayer coatings of ZrO₂–Y₂O₃–Al₂O₃ were prepared using the sol-gel method and dip-coating technique in order to advance in the study of what influence the incorporation of Al₂O₃ has on films of Y₂O₃-doped ZrO₂, investigating its role in the synthesis of the solutions and in the characteristics and properties of the coatings. After the characterization of the solutions used in the process, the microstructure of the films was studied and their mechanical behaviour and resistance to thermal shock were determined so as to optimize the characteristics and functionality of these coatings. With increased alumina content, 3YSZ-Al₂O₃ (20 mol%), the cubic phase of the zirconia disappeared completely at the sintering temperature used (700 °C), resulting in the tetragonal phase with Al in solution. There was also a decrease in the coatings' hardness and Young's modulus, and an increase in toughness and resistance to thermal shock. These results allow guidelines to be established for the design of multilayer structures that are, tougher, more resistant, and have improved surface properties.     

Investigation on thermal conductivity and mechanical properties of Si3N4 ceramics via one-step sintering

High thermal conductivity Si₃N₄ ceramics were fabricated using a one-step method consisting of reaction-bonded Si₃N₄ (RBSN) and post-sintering. The influence of Si content on nitridation rate, β/(α+β) phase rate, thermal conductivity and mechanical properties was investigated in this work. It is of special interest to note that the thermal conductivity showed a tendency to increase first and then decrease with increasing Si content. This experimental result shows that the optimal thermal conductivity and fracture toughness were obtained to be 66 W (m K)^-1 and 12.0 MPa m^1/2, respectively. As a comparison, the nitridation rate and β/(α+β) phase rate in a static pressure nitriding system, i.e., 97% (MS10), 97% (MS15), 97% (MS20) and 8.3% (MS10), 8.3% (MS15), 8.9% (MS20), respectively, have obvious advantages over those in a flowing nitriding system, i.e., 91% (MS10), 91% (MS15), 93% (MS20) and 3.1% (MS10), 3.3% (MS15), 3.3% (MS20), respectively. Moreover, high lattice integrity of the β-Si₃N₄ phase was observed, which can effectively confine O atoms into the β-Si₃N₄ lattice using MgO as a sintering additive. This result indicates that one-step sintering can provide a new route to prepare Si₃N₄ ceramics with a good combination of thermal conductivity and mechanical properties.     

Microstructure,mechanical properties and thermal conductivity of (Ti0.5Nb0.5)C–SiC composites

A series of (Ti_0.5Nb_0.5)C-x wt.% SiC (x = 0, 5, 10, 20) composites were prepared by spark plasma sintering. Dense microstructures with well‐dispersed SiC particles were obtained for all composites. With the increment of SiC content, the Vickers hardness, Young's modulus and fracture toughness increase monotonically. An optimized flexural strength of 706 MPa was achieved in (Ti_0.5Nb_0.5)C-5 wt.%SiC composite. (Ti_0.5Nb_0.5)C-20 wt%SiC composite exhibits the highest fracture toughness of 6.8 MPa m^1/2. The crack deflections and the suppression of grain growth were the main strengthening and toughening mechanisms. Besides, (Ti_0.5Nb_0.5)C-20 wt%SiC composite exhibit the highest thermal conductivity of 45 W/m·K at 800 °C.     

Microstructure evolution of CMAS glass below melting temperature and its potential influence on thermal barrier coatings

CaO–MgO–Al₂O₃–SiO₂ (CMAS) deposition significantly degrades the performance of thermal barrier coatings (TBCs). In this study, the microstructure evolution of CMAS glass at temperatures below its melting point was investigated in order to study the potential influence of temperature on the applicability of CMAS glass in TBCs. The CMAS glass fabricated in this study had a melting point of 1240 °C, became opaque, and underwent self-crystallization when the temperature reached 1000 °C. After heat treatment at 1050 °C, diopside and anorthite phases precipitated from the glass; at a higher temperature (1150 °C), diopside, anorthite, and wollastonite were formed as the self-crystallization products. An increase in the dwelling time resulted in the transformation of diopside to wollastonite and anorthite. At 1250 °C, all products formed a eutectic microstructure and melted. The results indicate that even at low temperatures, CMAS glass underwent microstructure evolution, which could influence the coating surface and stress distribution when deposited on TBCs.     

Cracking behavior and delamination mechanism of lamellar structured TBC with localized mixed oxides

Mixed oxide (MO) with localized growth feature and high growth rate remarkably affects the lifetime of thermal barrier coatings (TBCs), which indicates that clarifying the ceramic cracking mechanism induced by MO is critical for developing new coatings with high durability. Two kinds of TBC models involving spherical and layered mixed oxides are created to explore the influence of MO growth on the local stress state and crack evolution during thermal cycle. The growth of α-Al₂O₃ is also included in the model. The undulating interface between ceramic coat and bond coat is approximated using a cosine curve. Dynamic ceramic cracking is realized by a surface-based cohesive interaction. The ceramic delamination by simulation agrees with the experimental observation. The effects of MO coverage ratio and growth rate on the TBC failure are also discussed. The results show that the MO growth causes the local ceramic coat to bear the normal tensile stress. The failure mode of coating is turned from α-Al₂O₃ thickness control to MO growth control. Once the mixed oxide appears, local ceramic cracking is easy to occur. When multiple cracks connect, ceramic delamination happens. Suppressing MO formation or decreasing MO growth can evidently improve the coating durability. These results in this work can provide important theoretical guidance for the development of anti-cracking TBCs.     

Effect of particle grading on fracture behavior and thermal shock resistance of MgO-C refractories

Two types of MgO-C refractories with tight particle grading and non-tight particle grading were prepared according to Andreasen's continuous packing theory. Fracture behaviors were investigated using wedge splitting tests combined with digital image correlation method and acoustic emission techniques. The results indicated that MgO-C refractory with non-tight particle grading treated at 1400 ℃ had more in situ phases (e.g., AlN and MgAl₂O₄) and exhibited less brittleness than specimens with tight particle grading even though they had similar nominal tensile strengths. In contrast, specimens with non-tight particle grading had greater horizontal strain under various loading stages, reflecting their better ability to resist rupture deformation. In addition, more microcracks were initiated earlier in the pre-peak region, and more energy was consumed. The decrease in coarse particles and corresponding increase in fine powder content increased the interface between particles, benefiting for reducing the local stress concentration and improving the thermal shock resistance of refractories.